# S. M. ENTERPRISES

> Authorized sales partner of KLINGER in India


## Pages

- [Tanker Gate Valves - Double Gate, Double Wedge](https://www.sme-ama.com/products/tanker-truck-safety-fittings/tanker-gate-valves-double-gate-double-wedge/): Material of Construction : Phosphour Bronze Size : 80mm
- [Spark Arrestor](https://www.sme-ama.com/products/tanker-truck-safety-fittings/spark-arrestor/): This spark arrestor is so designed that it can be easily used on any Tanker Trucks/Lorries. Its fitting and cleaning are simple and easy. Does not affect engine power, parts or over-heat. Does not create back pressure in exhaust system.
- [Pressure cum Vacuum Valve](https://www.sme-ama.com/products/tanker-truck-safety-fittings/pressure-cum-vacuum-valve/): This valve is designed to be fitted in each compartment with an independent vacuum and pressure operated vent. Technical Data : Effective opening = 3 sq. cm. Pressure limit with in compartment = 021/1cm Vacuum limit = 5 cm. WG The P.V. value is designed as to prevent loss of Liquids through the valve in the case of vehicle upset.500
- [Mini Spark Arrestor](https://www.sme-ama.com/products/tanker-truck-safety-fittings/mini-spark-arrestor/): This spark arrestor is so designed that it can be easily used on any Tanker Trucks/Lorries. Its fitting and cleaning are simple and easy. Does not affect engine power, parts or over-heat. Does not create back pressure in exhaust system.
- [Fusible Plug for Emergency Vent](https://www.sme-ama.com/products/tanker-truck-safety-fittings/fusible-plug-for-emergency-vent/): Type”A” It is to be filled in each compartment of a tank with an emergency venting facility of fusible type. Technical Date: 2.5″ dia opening plug. 5 mm. thick fusible alloy plate which will operate at a temparature less than 93o C. The emergency vent is designed as to prevent loss of liquid through the vent in the case of vehicle upset.
- [Fusible Link](https://www.sme-ama.com/products/tanker-truck-safety-fittings/fusible-link/): This is secondary control over Shut-Off Valve provided with a fusible link, which will permit the Shut-Off Valve to close automatically in event of a fire.
- [Emergency Shut-off Valve](https://www.sme-ama.com/products/tanker-truck-safety-fittings/emergency-shut-off-valve/): This Shut-Off Valve is so designed that it can be easily used in any tanker truck/lorry with lever. Its fitting and cleaning are simple and easy. Does not affect any pipe lines or tank. In case break down at lever it can be opened from upper side
- [Tanker Truck Safety Fittings](https://www.sme-ama.com/products/tanker-truck-safety-fittings/)
- [KLINGERSIL Non Asbestos Sealing Gasket, Cushion Gasket](https://www.sme-ama.com/products/gauge-glass-accessories/klingersil-non-asbestos-sealing-gasket-cushion-gasket/): The Klinger group has been recognised as the market leader in gaskets and sealing for over a century. KLINGER’s research and development laboratories have investigated over 250 different fibre forms in the search for asbestos free alternatives. The search has resulted in a range of high quality and high performance asbestos free materials that have been proven in service.
- [KLINGERIT 3xA (CAF) Sealing Gasket, Cushion Gasket](https://www.sme-ama.com/products/gauge-glass-accessories/klingerit-3xa-caf-sealing-gasket-cushion-gasket/): Top quality sheet material for steam, gas, oil, water and non-aggressive services. Recommended for use for high temperatures and high pressures. Composed of styrenebutadiene binder with high-grade long-fibre chrysotile asbestos.
- [Mica Shields](https://www.sme-ama.com/products/gauge-glass-accessories/mica-shields/): Mica Shields provide the best care to flat transparent, sight glasses in water and liquid level gauges and columns in high pressure steam boilers. The Shields retain basic strength and increase the service life of sight glasses when used at increased steam pressures and high working temperatures. Mica Shields also provide perfect visibility for monitoring the nature or degree of combustion in blast furnaces of steam boilers.
- [Gauge Glass Accessories](https://www.sme-ama.com/products/gauge-glass-accessories/)
- [KLINGER Transparent Gauge Glasses](https://www.sme-ama.com/products/transparent-gauge-glasses/klinger-transparent-gauge-glasses/): KLINGER transparent glasses are manufactured from borosilicate glass (“extra-hard”). The surfaces on both sides are finely grounded and polished to ensure optimal transparency.
- [ILMADUR Transparent Gauge Glasses](https://www.sme-ama.com/products/transparent-gauge-glasses/ilmadur-transparent-gauge-glasses/): TGI sight glasses are world-leaders in terms of quality and safety. All the well-known, discerning fittings and instruments manufacturers and operators worldwide agree on one thing: ILMADUR® sight glasses “Made in Germany” by TGI are a real safe bet. TGI’s specially developed “I-420” borosilicate glass can withstand the highest loads. Whether you need to monitor fluid levels in chemical plants or complex processes in power plants, ILMADUR® sight glasses can resist both high pressures and extreme temperatures. And of course, their sight glasses comply with the latest DIN standards and the most important standards worldwide. But the hardest standard to meet…
- [Transparent Gauge Glasses](https://www.sme-ama.com/products/transparent-gauge-glasses/)
- [KLINGER Reflex Gauge Glasses](https://www.sme-ama.com/products/reflex-gauge-glasses/klinger-reflex-gauge-glasses/): The side facing the media chamber is provided with moulded grooves set at 90° angle. The moulding process increases the resistance of the glass grooves to wear; the skin which the glass attains during moulding gives it maximum smoothness and hardness. This makes it extremely resistant to the attack of boiler water.
- [ILMADUR Reflex Gauge Glass](https://www.sme-ama.com/products/reflex-gauge-glasses/ilmadur-reflex-gauge-glass/): TGI sight glasses are world-leaders in terms of quality and safety. All the well-known, discerning fittings and instruments manufacturers and operators worldwide agree on one thing: ILMADUR® sight glasses “Made in Germany” by TGI are a real safe bet. TGI’s specially developed “I-420” borosilicate glass can withstand the highest loads. Whether you need to monitor fluid levels in chemical plants or complex processes in power plants, ILMADUR® sight glasses can resist both high pressures and extreme temperatures. And of course, their sight glasses comply with the latest DIN standards and the most important standards worldwide. But the hardest standard to meet…
- [Reflex Gauge Glasses](https://www.sme-ama.com/products/reflex-gauge-glasses/): We stock Klinger Reflex and Transparent Glasses manufactured from high quality Borosilicate Glass ‘Extra Hard’ with a low thermal expansion coefficient guaranteeing perfect indication, maximum safety and outstanding suitability for use in liquid level gauges of nearly all makes.
- [Tube Wall Reducing Tools](https://www.sme-ama.com/products/tube-tools/tube-wall-reducing-tools/): The first stage in removal of a tube is the reduction of the rolled portion of the tube in the tube sheet. This tool enables the operation to be performed, the pilot maintaining the alignment in the tube bore. The tube can be removed with the Knock Out Tools. Shank Type: MT Please specify Gauge while placing enquiry
- [Tube Plugs](https://www.sme-ama.com/products/tube-tools/tube-plugs/): The ring-and-pin type plug, is designed to seal off leaking or damanged tubes in heat-exchangers and condensers. It ensures a uniform joint without damaging the tube-sheet. Place the ring in the tube then force the pin into the ring with a few sharp blows from a hammer until a tight seal is made between the ring and the tube bore. These plugs can be supplied in brass, steel or stainless steel for tubes in the range 1/2 inch (12.7 mms) to 1.1/4 inch (31.75 mms) O.D. The solid type tube plug is used to seal off a leaking or damaged boiler…
- [Tube Drifts (Knock Out Tools)](https://www.sme-ama.com/products/tube-tools/tube-drifts-knock-out-tools/): These tools are designed to use with either Hammer or Pneumatic Hammer. The pilot diameter is accurately machined to locate in the Tube ID whilst the main body of the tools forces the tube away from tube plate. Please specify Gauge & Shank Type while placing enquiry
- [Tube Collapsing Tools](https://www.sme-ama.com/products/tube-tools/tube-collapsing-tools/): These tools are used as collapsing tubes in the tube sheet and are used with either manual Hammer or Pneumatic Hammer. Please specify Shank Type while placing enquiry
- [Internal Tube Cutter - Manual One Revolution](https://www.sme-ama.com/products/tube-tools/internal-tube-cutter-manual-one-revolution/): For cutting nonferrous tubes in heat exchangers, condensers, boilers. Adjustable 2″ to 8″. Tools designed for manual operation employing Ratchet or Hand wrench of proper size to fit the square drive of the cutter.
- [Internal Tube Cutter - Machine Operated (Push Type)](https://www.sme-ama.com/products/tube-tools/internal-tube-cutter-machine-operated-push-type/): The Machine-Operated Tube Cutter cuts away fast and accurately through the walls of tubes in condensers and heat exchangers as a step in their removal from the tube sheets. Forward pressure in motor causes cutter to extend nearly serving of tube. Closely coupled cutter bit can be changed quickly and easily. Driven by standard electric or pneumatic motor. Standard reach 4 1/ 2″. Specify type of bits for ferrous / nonferrous.
- [Tube Guide (Pilot)](https://www.sme-ama.com/products/tube-tools/tube-guide-pilot/): The Plug consists of an aluminium tapered nose with a replaceable nylon brush attached. For easy inserting of tubes required to pass through tube sheets & baffle plates.
- [Tube End Facers](https://www.sme-ama.com/products/tube-tools/tube-end-facers/): This tool is suitable for facing tube ends flush to the tube sheet by the addition of a shroud will trim the ends which project from tube sheet. By changing the pilot bush the tool can be adapted to suit any particular gauge for a specific size. Facers supplied with hexagonal shanks. Facers also available with round shank and morse taper / square shank.
- [Fully Automatic Digital Torque Controller](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/fully-automatic-digital-torque-controller/): For Consistently Perfect Rolling Range : 1/4″ to 2 1/2″ (6.35 To 63.5 MM) OD Tubes. Phase : Single Supply Volts : 230 V The fully automatic solid state electronic torque controlled tube expanding controller is electrical and is based on the fact that under equal conditions the same amount of torque transmitted to an expander gives the same amount of expansion in tubes of identical sizes, gauge and material. The control unit consists of an electrical circuit, which accurately measures the amount of current to the Drive Unit, provides precise regulation of the Drive Unit. The Drive Unit is a…
- [400-F Series](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/boiler-tube-expanders/400-f-series/): for Bell-Mouth Expansion with 2 Parallel + Short Plain + Flare Expanders Also Supplied With Header & Short Series Mandrel. For ordering expanders specify tube size, expansion, length and type of mandrel. Expanders available with four roller & five rollers.
- [400 Series](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/boiler-tube-expanders/400-series/): for Parallel Expansion Fitted With 3 Parallel Rollers 3 Roller Parallel Expanders For Boilers, Economisers, Super-heaters, Air Heaters, Juice Heaters, Pan & Evarporators
- [Boiler Tube Expanders](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/boiler-tube-expanders/): These Boiler Expanders are self-feeding, parallel rolling, three expanding rolls and three flaring rolls with fixed roller length. Tools that roll and flare a tube in one operation. This type of expander is particularly suitable for rolling and flaring tubes in drums, super heater and economiser header having small plug or hand hole openings.
- [900 Series](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/heat-exchanger-condenser-tube-expanders/900-series/): for 1/4″ TO 3/8″ (6.30 TO 9.50mm)
- [8012 Series](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/heat-exchanger-condenser-tube-expanders/8012-series/): for 1.3/4″ TO 3″ (44.4 TO 76.2) OD
- [800 Type Five Roll Expanders](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/heat-exchanger-condenser-tube-expanders/800-type-five-roll-expanders/): for 1/2″ TO 1.1/2″ (12.7 TO 38.1 MM) OD
- [800 Series](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/heat-exchanger-condenser-tube-expanders/800-series/): for 1/2″ TO 1 1/2″ (12.7 TO 38.1 mm) OD
- [1300 Series](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/heat-exchanger-condenser-tube-expanders/1300-series/): for 3/8″ ( 9. 5 mm) OD
- [1200 Type Five Roll Expanders](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/heat-exchanger-condenser-tube-expanders/1200-type-five-roll-expanders/): for 1/2″ TO 1.1/2″ (12.7 TO 38.1mm) OD
- [1200 Series](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/heat-exchanger-condenser-tube-expanders/1200-series/): for 1/2″ TO 1 1/2″ (12.7 TO 38.1 mm) OD RANGE FITTED WITH 1 1/2″ (38.1) LG. ROLLER FITTED WITH 2 1/4″ (57.1) LG. ROLLER MINIMUM A. 12.7 MM (1/2″) 38.1 MM (1 1/2″) MAXIMUM B. 31.7 MM (1 1/4″) 57.1 MM (2 1/4″) For Oil Coolers, Air Coolers, Pre Heaters & Radiators Tube OD in. (mm) Tube Gauge bwg. in. (mm)   Tube ID in. (mm) Min. ID Tool Enters in. (mm) Maximum Expansion of Tool in. (mm) Tube Sheet Thickness Mandrel No. Mandrel Square Drive in (mm) 1-1/2 in. to 6 in. (38.1mm) (152.4mm) 2-1/4 in. to 6-3/4 in.…
- [Heat Exchanger & Condenser Tube Expanders](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/heat-exchanger-condenser-tube-expanders/): These Expanders produce smooth, unrigid surfaces in condenser, heat exchanger tubes. Designed for exceptionally long service, these tube expanders feature an adjustable ball bearing thrust collar to eliminate frictional heat. Rolls have gradually tapered nose to eliminate sharp offset in the rolled tubes and assure uniform tightness through out entire thickness of tube sheet. Size available 1 /4″ to 3″ (6.35 to 76.2 mm
- [Tube Expanding Equipments](https://www.sme-ama.com/products/tube-tools/tube-expanding-equipments/): Note : Control Panel & Drive Units are available in 110 V. & 230 V. A.C.
- [Flexible Extensions](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/flexible-extensions/): for cleaning bent tubes
- [Carbide Drills](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/carbide-drills/): for Heavily Choked Tubes Carbide Drills are used for cleaning tubes choked solidly with hard deposits.
- [Hand Held Tube Cleaners](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/hand-held-tube-cleaners/): The Hand Held Tube Cleaners use shafting of different diameters as per tube I.D. to be cleaned which can be coupled together to form lengths as per the length of the tube to be cleaned. Typical cleaning tools used are carbide drills for severly clogged tubes, brushes for light deposits and buffing tools for final polishing of tubes. Build your own kit by adding price of the Cleaner, Hollow Shafts, Drive Shafts, Shaft Coupling, Drive Coupling based on length of the tube to be cleaned and cleaning tools (Brushes / Drills).
- [Turk Head Brushes](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/brushes/turk-head-brushes/): Heavy Duty Turk Head Brush made from hardened and tempered Spring Steel Wires, with more construction number of wires per brush with nail and hydraulically pressed-heavy construction with 1/2″ BSW female threaded end for efficient cleaning of tubes.
- [Single Spiral Brushes](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/brushes/single-spiral-brushes/): Single Spiral & Double Spiral Brush is specially designed for tube cleaning having longer wire portion.
- [Multi-Purpose Brushes](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/brushes/multi-purpose-brushes/): This assembly consists of 1 to 4 circular brushes which can be used with flexible shaft for cleaning the toughest scale inside the tubes.
- [Double Spiral Brushes](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/brushes/double-spiral-brushes/): Single Spiral & Double Spiral Brush is specially designed for tube cleaning having longer wire portion.
- [Circular Wheel Brushes](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/brushes/circular-wheel-brushes/): For use with portable grinder
- [Nylon Brushes](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/brushes/nylon-brushes/): Models / Range Available: 006.4mm (1/4″) 007.9mm (5/16″) 009.5mm (3/8″) 011.1mm (7/16″) 012.7mm (1/2″) 014.3mm (9/16″) 015.9mm (5/8″) 017.5mm (11/16″) 019.1mm (3/4″) 020.6mm (13/16″) 022.2mm (7/8″) 023.8mm (15/16″) 025.4mm (1″) 031.7mm (1.1/4″) 038.1mm (1.1/2″) 044.5mm (1.3/4″) 051.0mm (2″) 057.1mm (2.1/4″) 063.5mm (2.1/2″) 070.0mm (2.3/4″) 076.2mm (3″) 082.6mm (3.1/4″) 089.0mm (3.1/2″) 095.2mm (3.3/4″) 101.6mm (4″) Other sizes can be made on request.
- [Brass Brushes](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/brushes/brass-brushes/): Models / Range Available: 006.4mm (1/4″) 007.9mm (5/16″) 009.5mm (3/8″) 011.1mm (7/16″) 012.7mm (1/2″) 014.3mm (9/16″) 015.9mm (5/8″) 017.5mm (11/16″) 019.1mm (3/4″) 020.6mm (13/16″) 022.2mm (7/8″) 023.8mm (15/16″) 025.4mm (1″) 031.7mm (1.1/4″) 038.1mm (1.1/2″) 044.5mm (1.3/4″) 051.0mm (2″) 057.1mm (2.1/4″) 063.5mm (2.1/2″) 070.0mm (2.3/4″) 076.2mm (3″) 082.6mm (3.1/4″) 089.0mm (3.1/2″) 095.2mm (3.3/4″) 101.6mm (4″) Other sizes can be made on request.
- [Stainless Steel Brushes](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/brushes/stainless-steel-brushes/): Models / Range Available: 006.4mm (1/4″) 007.9mm (5/16″) 009.5mm (3/8″) 011.1mm (7/16″) 012.7mm (1/2″) 014.3mm (9/16″) 015.9mm (5/8″) 017.5mm (11/16″) 019.1mm (3/4″) 020.6mm (13/16″) 022.2mm (7/8″) 023.8mm (15/16″) 025.4mm (1″) 031.7mm (1.1/4″) 038.1mm (1.1/2″) 044.5mm (1.3/4″) 051.0mm (2″) 057.1mm (2.1/4″) 063.5mm (2.1/2″) 070.0mm (2.3/4″) 076.2mm (3″) 082.6mm (3.1/4″) 089.0mm (3.1/2″) 095.2mm (3.3/4″) 101.6mm (4″) Other sizes can be made on request.
- [Brushes](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/brushes/): We can also make custom brushes according to your sample / drawing.
- [Swing Frame Cutter Heads](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/cutter-heads/swing-frame-cutter-heads/): For Tubes/Pipes 2″ – 4″ (51.0mm-101.6mm) I.D. These Cutter Heads have 3 to 5 freely pivoted arms, activated centrifugally, which swing out to give access to any part of tube wall.
- [Swing Arm Cutter Heads](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/cutter-heads/swing-arm-cutter-heads/): This type of cutter consists of four arms and four taper cutter wheels and is used where scale conditions vary.
- [Single Head Cutter](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/cutter-heads/single-head-cutter/)
- [Pivoted Arm Cutter Heads](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/cutter-heads/pivoted-arm-cutter-heads/): For Tubes/Pipes 1.1/2″ – 4″ (38.1mm-101.6mm) I.D. These cutter heads produce excellent results in curved or straight tubes. Pivoted arms of cutter Heads swing out by centrifugal force so that the cutters contact every part of the tube wall.
- [General Purpose Cutter Heads](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/cutter-heads/general-purpose-cutter-heads/)
- [Drill Head Cutter](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/cutter-heads/drill-head-cutter/)
- [Boring Tool Head Cutters](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/cutter-heads/boring-tool-head-cutters/): This cutter head is designed for opening up badly choked up tubes in condenser, evaporator and smoke tubes in sizes of 32 to 50 mm.
- [Arrow Head Cutters](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/cutter-heads/arrow-head-cutters/)
- [6 Wheel Cutter Heads](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/cutter-heads/6-wheel-cutter-heads/): This cutter head is designed for cleaning straight and curved tubes as found in Boilers, Air Heaters, Economisers, etc. It consists of 6 cutter wheels, two each of straight teeth, teeth cut right hand and teeth cut left hand for quicker and efficient cleaning of tubes
- [3 Wheel Cutter Heads](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/cutter-heads/3-wheel-cutter-heads/): For Tubes/Pipes 1.1/4″ – 4″ (31.7mm-101.6mm) I.D. This cutter head is designed for cleaning straight and curved tubes as found in Boilers, Air Heaters, Economisers, etc. It consists of 3 cutter wheels, one each of straight teeth, teeth cut right hand and teeth cut left hand for quicker and efficient cleaning of tubes and prevent grooving of scale.
- [15 Wheel Cutter Heads](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/cutter-heads/15-wheel-cutter-heads/): For Tubes/Pipes 1.1/4″ – 2″ (31.7mm-51.0mm) I.D. These spring loaded, self expanding cutter heads are designed for rapid removal of hard and obstinate scale formation in straight tubes as found in Evaporators, Juice Heaters, etc. It consists of 3 bevel, 4 straight cutter wheels, 4 left cutter wheels and 4 right cutter wheels, fitted on three bridge type arms.
- [Cutter Heads](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/cutter-heads/): DYNAFLEX™ cutter heads are designed for efficient and effective removal of hard scale from tubes. All parts are made from high quality steel, properly hardened and tempered to ensure long life.
- [Flexible Shafts](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/flexible-shafts/): DYNAFLEX™ Extra Heavy Duty Flexible Shaft consisting of double wound inner core made of best grade tested spring steel wire passed through stress releasing process made for absolute vibration free performance. It is treated with oil and chemically tempered with special technique to withstand heavy load to prevent twisting and breaking. Outer casing is manufactured from galvanised steel material specially suitable for flexible shafts and is provided throughout its length with spring steel flat coil antifriction lining. The flexible shaft is provided with ball bearing hand piece, guard and coupling in one single piece with out any joints.
- [Electrically Driven Tube Cleaners](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/electrically-driven-tube-cleaners/): DYNAFLEX™ electrically driven tube cleaner is mounted on a 3 wheel heavy duty trolley with a pull handle, the motor used is of KIRLOSKAR make, ISI tested and fully guaranteed. It is 3 phase, 415 volts, 50 cycles, 3000 RPM, TEFC, cage induction motor with a suitable Siemens / L&T starter. The Machine is fully wired and carefully tested with a 10 feet Finolex PVC cable to the main supply but without flexible shaft.
- [Tube Cleaning & Descaling Equipments](https://www.sme-ama.com/products/tube-tools/tube-cleaning-descaling-equipments/): When tube cleaning is a problem, you can be sure to find the right answer in one of the DYNAFLEX cleaners. It is a range of efficient, well made tube cleaners that have been engineered to perform even on the hardest of all scales and have rapidly earned the respect of engineers in many industries. The application range is wide: boilers, condensers, heat exchangers, super heaters, service pipelines, etc. and in many cases S. M. Enterprises can adapt these cleaners to match special requirements. Why Clean Tubes? To function efficiently every tube type heat exchange device, whether a hot water or…
- [Tube Tools](https://www.sme-ama.com/products/tube-tools/)
- [Products](https://www.sme-ama.com/products/)
- [Terms of Use](https://www.sme-ama.com/terms/): The information, layouts and design elements provided on this website are subject to copyright. Partial or complete duplication or any other utilisation of the contents on this website is prohibited without written permission from S. M. Enterprises. Disclaimer All information and details have been carefully researched and processed. However, S. M. Enterprises does not guarantee that the information is complete and correct. S. M. Enterprises assumes no liability for any damage resulting directly or indirectly in the context of the use, abuse or functionality of this website and the information it contains. Any reference made to other websites does not in…
- [Blog](https://www.sme-ama.com/blog/)
- [Contact Us](https://www.sme-ama.com/contact/): S. M. ENTERPRISESD1, Plot 68, C. L. Mehta SalaiThoraipakkamChennai 600097, INDIA +91 960 013 2488, +91 984 006 5966 theteam@sme-ama.com or use the form below to send us an email. Please make sure to type in your email address correctly or we might not be able to reply to your message.
- [Home](https://www.sme-ama.com/): KLINGER Borosilicate Gauge Glasses KLINGER AB Cocks KLINGER Ball Valves KLINGER Piston Valves “It’s unwise to pay too much, but it’s worse to pay too little. When you pay too much, all you lose is a little money – that is all. When you pay too little, you sometimes lose everything because the thing you bought was incapable of doing the thing it was bought to do. The common law of business balance prohibits paying a little and getting a lot – it can’t be done. If you deal with the lowest bidder, it is well to add something for the…
- [Privacy Policy](https://www.sme-ama.com/privacy/): At S. M. Enterprises, your privacy is our priority. We are committed to protecting your privacy at all times, in all situations. This privacy notice discloses the privacy practices for this web site. This privacy notice applies solely to information collected by sme-ama.com including all of its subdomains. It will notify you of the following: What personally identifiable information is collected from you through the web site, how it is used and with whom it may be shared. What choices are available to you regarding the use of your data. The security procedures in place to protect the misuse of your…

## Optional

- [Agent (MCP protocol)](websites-agents.hostinger.com/www.sme-ama.com/mcp)

[comment]: # (Generated by Hostinger Tools Plugin)